Sign In | Sign Up to Shop/Forum

Winter Maintenance of my Tenkara Gear

On December 17, 2012
Comments (5)

Last year I had the pleasure of meeting Jay Pape at the first Tenkara Summit. Jay works for the National Forest Service out of Bozeman, Montana, and this year I had the opportunity to get to know and fish with him when I was visiting the area. I’m very thankful for his submission of the very helpful article that follows on gear maintenance.

Written by Jay Pape

Tenkara rod taken apart

Now that snow and ice has closed most of the local streams here in Bozeman, I use the long Montana nights to tie kebari and reflect on the many days enjoyed tenkara fishing this season.

Highlights of my last day on the water include sleet and snow plastered to my beard, a furled line frozen stiff by the wind AND a handful of beautiful rainbow trout. Back at the truck numb fingers struggled to collapse my 12’ Iwana and each section made nasty noises as they nested into each other. I didn’t

dare collapse the tip sections and quickly drove home to let everything thaw out.  At this point the harsh realization set in- my season was over for a while and a bit of winter maintenance was in order.

Here are few tips to make sure your tenkara gear will be ready to go as soon as the streams open up:

  1. Remove the end cap and slide out each section of the rod. I then place them on towel to keep them from rolling onto the floor.Tenkara rod cleaning
  2. With a turkey baster or syringe full of warm water I flush the inside of each section and blow any remaining water out before.
  3. When everything is dry I use a clean cloth saturated with denatured alcohol to wipe down each section. This removes the residue on the thicker end and evaporates quickly. Warm soapy water also works well.Cleaning a tenkara rod
  4. Before reassembly I inspect the Lillian for damage and lubricate each section with Tri-Flow applied to another lint-free cotton rag or pad. TriFlow is a dry lubricant that repels dust/dirt and isn’t greasy like WD40.Lubricating tenkara rod
  5. When my rod was new, I wanted to keep the cork grip from getting covered with black, sweaty grime. To prevent this, I applied a few coats of Zinsser Clear Shellac. If the shellac looks worn, I add a fresh coat.
  6. Once everything is dry, I apply a fresh wrap of white, PTFE (plumbers) tape to help keep the screw cap snug [note from Daniel: the newer tenkara rods have an o-ring on the caps, which prevents them from unscrewing, PTFE tape should not be necessary]. The rod tube also gets a thorough cleaning and the threads are dabbed with Tri-Flow to keep the end caps from binding.
  7. To clean the mesh of the tamo I fill the kitchen sink with hot soapy water, soak and rinse. This should be done after every outing to prevent the transport of invasive species. This is also a good time to inspect the net bag and make any needed repairs.Cleaning tenkara rod and tenkara net
  8. Lastly, I wash my smelly waders and boots and let them air dry before storing them in my fishing bin.

I also go through all of my lines and replace the tippet rings or perfection loops. With everything put away in good condition I can tie kebari (and ski powder) knowing that I am ready to enjoy the streams as soon as the weather breaks.

Facebook Comments


» Tenkara DIY, Tenkara Gear, Tenkara Nets, Tenkara Rods » Winter Maintenance of my Tenkara...
, , , , ,

5 Responses to Winter Maintenance of my Tenkara Gear

  1. Great article, Jay. I have to think that if you take this kind of care of your rod, you will greatly increase its life. Don’t worry, the weather here will break soon. Of course then the wind will probably howl like a banshee.

  2. Jay Pape says:

    Thanks, John. Maybe we can try a little Tenkara ice fishing this winter. I know this place just south of town…

  3. […] Winter is a slow fishing season around here. We get out, but is not the hectic pace of the other seasons. For me it is R & R time; reorganize and repair. He is a great post on cleaning those tenkara rods before they sit out the season in your new rack. Check out Winter Maintenance of my Tenkara Gear. […]

  4. mike says:

    this is a great post. i dig the Zinsser Clear Shellac idea. i recently rediscovered shellac when refurbing my hardwood floors. it is awesome. as for the rest of the post, i just want to make certain that using triflow and denatured alcohol are “ok”.


  5. Kevin says:

    Hey Jay if you ever see this Kevin from Reno says hey.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

« »